How to enter the router, in the settings: instructions for different models of routers

An article on how to enter the settings panel and connect to the Internet using a network cable or Wi-Fi point for TP-Link Routers, Dr. Link, Zixel, Asus, Nonggir, Hauwie, Rostelecom.

Log in to the router settings panel: General scheme

For what purposes should be included in the router settings?

• to independently configure the parameters.
• for password change.
• for the new name of its network Wi-Fi.

Appearance of router

Methods access

• using a network cable through a computer device.
• using the entrance Wi-Fi from a cell phone.

Log in to the TP-LINK router settings panel

Scheme:

• we carry out the compound K. Wi-Fi Router: At the entrance Wi-Fi Or with a network cable. In the settings panel TP-LINK. Entry from the tablet, laptop, computer, smartphone.

• open the browser ( mozilla. Firefox., the Internet Explora or others), pass at the following address 192.168.1.1 or 0.1 (in the end). The address is usually indicated at the bottom of the router.

View address, factory password and login on the rear panel of the router

• we view a request for login and password: Admin - default.
• log in to the router settings TP-LINK. implemented.

Detailed scheme:

• inbox, network cable, connect to a computer device. The connector on the router is marked with yellow (see Figure below).

Connection of the router with a computer device using a network cable

• in the browser search bar specify 192.168.1.1 for TP-LINK.. You can find this address on the bottom panel of the router (see Figure above). There will also be login, the default password.
• go to the specified address in the browser.
• in the emerging window, enter standard login and password or specify your own.

Go to the specified address in the browser, enter standard login and password or specify your

• we view the opened settings control panel.

The setup control panel is open

Log in to the D-Link Routher Settings Panel

There are two ways to connect to the Internet: using a network cable and through the entrance Wi-Fi

Option number 1

• connect the computer and router, as shown in the figure, using a power cable. In the router, for this purpose, we use one of their four inputs LAN.

Connect the computer and the router using a special entrance

Option number 2 (via Wi-Fi input)

• we find input Wi-Fi On a computer, laptop, choose a network DIR-615 For router D-Link,press key "To plug".
  

We find the Wi-Fi input on the computer, laptop, select the DIR-615 network for the D-Link router, press the "Connect" key

• we look at the password, which is listed on the bottom panel of the router. Password name WPS PIN.

We view the password that is listed on the bottom panel of the router.

• we enter the control panel to the address 192.168.0.1. This address is specified on the panel sticker (see photo).

We enter the control panel at 192.168.0.1.

• in the browser line enter the address.

In the browser line I enter the corresponding address

• we celebrate the standard password, login on the page that opens.
• press key "Ready."

We activate the "Finish" key

• open the option "System".
• we activate the key "Okay" or "Save."
• the entrance is made.

Login to the Router Zickel settings panel

The input scheme is similar to those indicated above, with the presence of small nuances:

• connect the connecting electrical cable to the connector Lan., entitled "Home network".

We connect the connecting electrical cable to the LAN connector, called the "Home Network"

• the second end of the electrical cable is applied to the computer device input.

The second end of the electrical cable is applied to the computer device

• drink a router from the AC network by connecting to the outlet.
• introduce the name in the web browser string 192.168.1.1As indicated in the picture.
• open the browser, with the inscribed web address of the settings.
  

  The web address of the settings is located on the bottom panel of the router.

• press key "Okay", We go beyond the same address.
• we view the emerging window with the key "Web Configurator" or "Fast setting".

We view the emerging window with the "Web Configurator" or "Fast Setup" key

• press key "Fast setting"Finding into the settings of the router.
• in the settings, a window for entering a password and login will appear for the initial entrance. Try to remember or write data for the future.

Enter the password and login to the window that opened.

• after entering the password and login input to the settings Zyxel. Completed.

Log in to the ASUS Routher Settings Panel

Connection diagram Standard:

• connecting a network cable to a router or input wi-Fi
  Login to the browser.
• go to the address in the settings.
• changing settings from tablet, laptop, computer, phone.
• address string in settings, next 192.168.1.1.
  So, detailed scheme:
• we look around the drawing, how to connect the cable to the connector Lan. and to the input of the computer device.

Connect the cable to the LAN connector and to the computer input

• we connect the power to the router device.
• we consider the option of connecting using the entrance wi-Fi. If there is a new router, after connecting the power, the Internet transmission will start with the title ASUS.
  

  Internet transmission with ASUS title

• open the browser by entering 192.168.1.1
• we view the settings page ASUS.

We view the ASUS settings page

• the data for the login from the manufacturer are on the bottom panel of the router.
  

  Data for the login from the manufacturer are on the bottom panel of the router

Log in to the Router Netgir settings panel

With respect to this Ruthera, do not forget several rules:
Login - Admin, password - password. set in mode "default".

If the router setting is carried out by the service center specialists, they change the password to the number of the router series. In the future, when rebooting should also, use the number of the series.
Key Reset. Responsible for resetting settings. The key is located on the bottom panel of the device.

Logging circuit in the settings panel:

• we enter the network - the Internet.
• in the browser line we enter the address http://192.168.1.1, password - Admin., password - password.

In the browser line, enter the address http://192.168.1.1, password - admin, password - Password

• change the password from the factory number to your personal information, pressing the key "Set password".
• enter the factory password code in the string "Old password".
• enter a new password in the password setup line
• repeat a new password in the appropriate line "Repeat a new password."

We carry out the installation of a new password

• we find the option "Wireless connection settings".
• enter into the string "SSID" Network name.
• we celebrate the country - Russia.
• we celebrate the channel - automatic.
• indicate the mode before 54 Mbps.
• we celebrate the "bird" string WPA2-PSK [AES].
• enter the code that includes an arbitrary set of digital signs (from 8 to 63), remember or recorded. Recommended to enter the number of the device series.
• we activate the key "Apply."

Through the option "Wireless connection options" option, we will take certain procedures, press the "Apply" key.

• entrance to the panel "Settings" Completed.
• set up PPPoe Connecting to the Internet network, entering the login and password specified in the contract of the company - the seller (a copy - a memo is included in the package).
• we celebrate the "point" mode "Apply the MAC address of the computer."
• we activate the key "Apply."

Entry to the Huawei Routher Settings Panel

To connect a router with a worldwide network, a fiber optic communication line is used.
The equipment includes the following:

• entrance WAN. To connect the fiber optic line
  knot W-IFI.
• connectors ADSL for TV. and IP- andphony (2 connector).
• connectors Lan. To connect home electrical equipment (4 inputs).

Device setup circuit Huawei.:

• attach the router to your home computer.
• connect the device with the operator's network - provider.

Note: After certain operations, you will use the Internet network from Rostelecom using a connecting cable connected to the input Lan..

• connect the cable from the provider to the last entrance Optical.Located on the left on the back wall of the router.
• connect home PC to the connector Lan. (You can use any of four), using a switching cord (included in the package). Using IP telephony or television Use the entrances Tel1 and Tel2.
• connect the device Huawei. to the electrical network of alternating current (outlet).
• start setting the characteristics to work in the operator zone RostelecomBy entering the address of the device located on the label below.
• if the label is torn, find out the address by clicking on the icon WindowBy opening the tab "Control center…" By hyperactive link.
• enter the option "View active"by clicking the link of local joining.
• activate the option "Intelligence".

After the operations mentioned above, press the "Details" key

• find a string "Gateway", copy the address, insert it into the browser string, press the key. "Okay" For the entry and the Internet.

Find the "Gateway" string, copy the address, insert it into the browser string, press the "Okey" key to enter the Internet and

• enter the login and password under the system request (information about them is located on the rear panel of the device). In case of change settings, type the code "Telecomadmin" + "Admintelecom" and "Root" + "Admin" To enter.
• authorization is carried out.
• go to Internet connection settings.

Internet connection scheme:

• on the First Software page Huawei., appeared as a result of authorization, enter the option "WAN".
• put an "bird" at the point "Enable WAN".

Intensify the "Enable WAN" item

• in line "MODE" Select "ROUTE" (route).
• in line "Service List" (service page) Turn on the parameter "The Internet"
• select the protocol PPPoe For acquisition IP addresses
• enter the password and login (under the contract (copies) attached to the device kit)
• in the case of connections not by fiber optic communication line, but through the network Etherne.Specify Lan. - Log where you connected the network cable from Rostelecom
• activate key "Apply"
• setup implemented

Routher settings diagram Huawei. Cherne input Wi-Fi:

• open the option "WLAN" (Menu at the top).
• put an "bird" opposite the option "WLAN" (Turning on).

Put "Bruis" in front of the "WLAN" option (inclusion)

• press the key "NEW".
• enter the name of the wireless network in a special line.
• activate the option "Enable SSID".
• mark points "Broadcast" and "WWM".
• select a parameter "WPA2" in line Authentication Mode » (Data protection option).
• specify a mixed password encryption option. "TKIP \\ AES".
• create your security password, mark it in the line "Pre-Shared Key".
• activate key "Apply."
• setting up router Huawei. Through input Wi-Fi Implemented.

Information on the entry addresses in the router settings panel

• address - router 192.168.1.1 or 192.168. 0.1 For device TP-LINK.
• address 192.168.0.1 For device D-Link.
• address 192.168.1.1 For device Zyxel.
• address 192.168.1.1 for device ASUS.
• address http://192.168.1.1 For device NetGear.
• input and Internet connection circuit for Huawei. See the section above.

In this article, we tried to show how to show, briefly and schematically show how to enter the settings panel and connect to the Internet using a power cable or point Wi-Fi For routers TP-Link, Dr. Link, Ziksel,  Asus, Nedegir, Jow Rostelecom.

We tried to specify addresses - login routers in the settings panel for each router.

Video: How to enter the router settings?